UniKL IR: Recent submissions

  • Applied Statistic 
    UNIKL MITEC (2013-11-01)
  • Basic Hydraulic System Mock-Up 
    Hishamudin Bin Saimi , Muhammad Nur Helmi Bin Basiran (2013-10-24)
    The Basic hydraulic system is the system that uses engines to move the landing gear, flight control, wheel and brakes and wing flap. The system located in the bottom part of fuselage, acting as a system that drive almost ...
  • Fuel Drum Lifter 
    Syed Azrin Bin Syed Ayub , Mohd Syamil Bin Rozman (2013-10-24)
    Fuel drum lifter is essential in order to move a heavy drum from one place to another. The load of a 55 gallon fuel drum would be too much too move without the aid of any mechanism. Therefore, we created the fuel drum ...
  • Cessna 182 Storage And Preservation Via Corrosion Control 
    Mohd Shahir Bin Saari , Ahmad Hanafi Bin Saharudin (2013-10-24)
    Alhamdulillah, we finally manage to get the title for our final year project based on the discussion with our supervisor, Mr. Md. Khairul Amiza bin Md. Hairuddin, which is to study about Cessna 182 storage and preservation ...
  • Flight Control Mockup 
    Luqman Nurhakim Bin Rosmadi , Muhammad Asyraf Bin Ahmad Khairi (2013-10-24)
    The main objective of constructing this project is to create a training aid that will be useful for the learning process specifically for ‘Flight Control’ learning process. This project will help to improve UniKL MIAT’s ...
  • Maintenance Time Prediction For Aircraft Turbine Engine Components; Removal And Replacement 
    Syaza Nurnadia Binti Abdul Sani (2013-10-24)
    The purpose of this research is to verify maintenance prediction time of aircraft turbine engine components on Removal and Replace (R&R) concept. This is carry out by applying Procedure III as stated and published in ...
  • Studies On Unmanned Aerial Vehicle’s Rotating Wing And Flight Control 
    Mohamed Arshad Bin Abdul Rahabudeen (2013-10-24)
    UAV with rotating wing is an aircraft configuration that uses a simple cross-flow fan mounted in the wing to provide distributed propulsion and augmented wing lift at very low flying speeds. The concept here is we are ...
  • Design And Manufacturing Of Fuselage And Landing Gear Assembly Of Unmanned Aerial Vehicle (Vibration) 
    Hariz Iskandar Bin Mansor (2013-10-24)
    This project is basically about designing and manufacturing the fuselage and landing gear system for an UAV. The fuselage must be able to withstand the vibration create from the engine. While the landing gear must be able ...
  • Analysis & comparison on the consumption of the fuel ( Petrol ) Between Stock Engine Control Unit ( ECU ) & The Engine Management ( E-Manage ) 
    Wan Ahmad Danish Wan Roshdi (2013-10-23)
    All modern vehicles today include an Engine Control Unit (ECU). This unit is responsible for the co-ordination of all sub systems of the vehicle such as the fuel ignition system. The ECU reads sensor values from various ...
  • Smart Pryly: Prototype Manufacturing And Pilot Testing 
    Simon Peter Dawson (2013-10-23)
    The purpose of this prototype is to achieve three main targets or objectives which are to design a trolley with a combination of prying function which will be able to remove the respective tire from its axle without damaging ...
  • IMPORTANCE OF AIR LEGISLATION 
    IZUAN BIN ZULHAM , AHMAD KHURSHID FAHMI BIN ABDUL KADIR (2013-10-23)
    This project is about the importance of Air Legislation. The aim of this project is to let the students of UNIKL MIAT know why Air Legislation is so important and that they should not take it lightly. Students should know ...
  • Compressor Adaptability For A Specific Cooling System 
    Mohamed Najmie Bin Shaik Ahamed (2013-10-22)
    During the past decade, increasing uses of R134a refrigerant in many type of cooling system have been attributed to poisoning of atmosphere. Exposure to dangerous levels of refrigerants R134a that have been used now days ...
  • Reducing Human Error Related Hazard In Aircraft Maintenance Environment 
    Abdullah Ahmed Farhan Al-Zaheri (2013-10-22)
    The purpose of this project is to give and gain knowledge to student so the know why human factors (HF) is importance due to maintenance in aircraft .Also show that the human error is cid as a major causal factor in most ...
  • Basic Pa System Mock-Up 
    Mohd Nur Irfan Bin Mohd Yusoff, Ashwinder Singh A/L Bharmjit Singh (2013-10-22)
    The final year project aims at exposing the students undergoing higher technical studies to the thoughts and logic that must be developed to ensure that one is able to integrate his/her ideas into something concrete.This ...
  • The Comparison Study Between Aviation Jet A-1 And Super Bio-Jet Fuel (Jatropha Based) Usages On Allison 250 Mockup Gas Turbine Engine 
    Mohd Haziq Bin Tajuddin (2013-10-22)
    The petroleum reserve depletion and the need to reduce the cost usage have encouraged increasing research on alternative fuel. Vegetable oils exploited to create Bio-jet Fuel. The Jatropha tree is natural grown in tropical ...
  • Piezoelectric Effect On Generation On Electricity 
    Mohamed Idris Bin Abdullah (2013-10-22)
    This thesis discusses the use of piezoelectric material to generate electricity Piezoelectric materials were known as smart materials due to the ability to produce electricpotential in response to applied mechanical actions. ...
  • PRODUCTION, PURIFICATION AND CHARACTERIZATION OF TANNASE ENZYME FROM Aspergillus niger BY SUBMERGE FERMENTATION 
    NUR ADILA BINTI NOR HANIF (2013-10-17)
    Tannase is an industrially important enzyme that is mainly used in the food, chemical, beverage and pharmaceutical industry. Tannase is responsible for the hydrolysis of ester and depside linkages in tannins to liberate ...
  • CHARACTERIZATION AND ADSORPTION STUDY OF CASSAVA PEEL FOR REMOVAL OF COPPER 
    ALI IMRAN BIN MOHAMAD (2013-10-17)
    The aim of this study is to investigate ability of cassava peel to remove Cu(II) in synthetic waste water. The cassava peel was value added by converting to biosorbent for Cu(II) removal. First of all, dried cassava peel ...
  • PURIFICATION AND OPTIMIZATION OF MANNOSE BINDING LECTIN FROM BOVINE’S LUNG TISSUE 
    NUR FARAHIYAH AZIM BINTI MD HASSAN (2013-10-17)
    Mannose binding lectin (MBL) is calcium dependent serum protein that used as a natural immune response and made in the liver. MBL works by binding to carbohydrates on the surface of pathogens where it can activate the ...
  • CHARACTERIZATION OF CHICKEN EGGSHELL AND IT'S BIOSORPTION ABILITIES 
    NURULAIN BINTI ZAINI (2013-10-17)
    In this study, adsorption study has been conducted to determine the feasibility of chicken eggshell as an adsorbent by removing the crystal violet solution. There are 3 parameter were investigated, which are pH, concentration ...